Home News News How To Select A Negative-Pressure Sensor For Robotics—HBP1101, HBP1201, And HBP1311 Compared

Releasetime:09.11.2026   Visits:38

How To Select A Negative-Pressure Sensor For Robotics—HBP1101, HBP1201, And HBP1311 Compared
Selecting a negative-pressure sensor for robotics is less about comparing raw specifications and more about matching the package form and assembly method. The HBP1101, HBP1201, and HBP1311 families from HBGK (Wuxi Haobang Hi-Tech Co., Ltd.) sit at the same performance level in range, accuracy, and operating temperature range, and all three offer both analog and digital I²C output variants. The differences are concentrated in package form and assembly method. For batch-assembly applications such as robot vacuum gripping, these two factors often determine project cost and delivery lead time earlier than accuracy does.


1. Dispelling a Common Misconception: Similar Spec Sheets Do Not Mean Drop-In Interchangeability
The most common path an engineer takes when selecting a negative-pressure sensor is to compare accuracy, range, and temperature drift on the spec sheet and pick the device with the 'best' figures. But when several families are already at the same level of measurement capability, this path breaks down — because what actually determines whether a device can be mounted cleanly on your board and shipped on schedule are engineering attributes that never appear on the spec sheet.
In a robot end-effector, vacuum detection points typically number between four and eight. The sensor must be assembled — together with pneumatic tubing, the control board, and structural parts — into the narrow wrist space, and must convert the measured negative pressure into a digital or analog signal in real time for the PLC, the robot controller, or an MCU to act on. Whether the package is surface-mount or through-hole, and whether reflow soldering is required, will directly rewrite your production-line plan and BOM.

● One-line conclusion: selecting a negative-pressure sensor for robotics is not about choosing performance — it is about choosing an assembly method.
● Recommended judgment order: first confirm annual volume and whether you have an SMT line, then whether the design is frozen, and finally the package and pin resources. Once these three are settled, the model is essentially decided.



2. Core Differences Across the Three Families: Package Form and Assembly Method
2.1 Primary Difference — Package Form and Assembly Method

● HBP1101 uses a SOP6 surface-mount package that suits fully automated SMT placement lines and has the smallest board footprint of the three.
● HBP1201 uses a DIP6 through-hole package that can be hand-soldered and repeatedly removed and replaced, making it ideal for prototyping, repair, and development verification.
● HBP1311 uses a SOP8 surface-mount package on the SMT route, with more generous pin resources.
This is where the three families diverge most clearly from an engineering standpoint.

2.2 Reference Item — Supply Voltage Range

● HBP1101: 1.8–3.6 V (digital), 5 V (analog);
● HBP1201: 3.6–5 V;
● HBP1311: 1.8–3.6 V (digital), 1.8–5.5 V (analog).
The digital variants share the same supply range, while the analog variants differ slightly. Actual robot negative-pressure detection usually lands on the two common nodes of 3.3 V or 5 V, so this difference is not a decisive selection dimension and is listed for reference only.

2.3 Reference Item — Output Type
All three families offer both an A (analog voltage) and a D (digital I²C) variant, with little difference between them. Digital variants connect directly to the bus of a PLC, robot controller, or MCU, eliminating an external ADC and its debugging; analog variants suit solutions that already have a mature acquisition chain and wish to keep the existing amplifier circuit. Both output types can be customized on request.
In summary, the three families are at the same level of measurement capability, with highly consistent output types and overlapping supply ranges. The core of robot negative-pressure selection is the assembly method — it determines whether the device can squeeze into the wrist alongside the suction cups, go straight onto a reflow line, and be swapped out quickly during board revisions.
There is also an easily overlooked reality: a single robot end-effector often carries four to eight negative-pressure detection points at once. The more points there are, the more device consistency and assembly efficiency are amplified — a single device that fits poorly or drifts in reading will drag down the yield and cycle time of the entire pick line.

3. Three-Family Parameter Comparison

Parameter HBP1101 HBP1201 HBP1311
Package SOP6 DIP6 SOP8
Assembly Surface-mount (SMT) Through-hole (THT) Surface-mount (SMT)
Dimensions 7 × 7 mm 7 × 7 mm 7.3 × 7.3 mm
Supply voltage Analog 5 V; digital 1.8–3.6 V 3.6–5 V Analog 1.8–5.5 V; digital 1.8–3.6 V
Output HBP1101A analog / HBP1101D I²C HBP1201A / HBP1201D HBP1311A / HBP1311D (customizable)
Pressure range −100 to +1000 kPa gauge; negative-pressure −10–10 / −35–0 / −100–0 kPa Same Same
Accuracy 0.5% FS (digital) Same Same
Temperature compensation On-chip, class-leading drift Same Same
Long-term stability Low annual drift Same Same
Operating temperature −40 to +85 °C Same Same
Calibration Factory-calibrated, plug-and-play Same Same

4. Direct Recommendations by Operating Condition
Operating condition Recommended model Reason
Fully automated SMT line, high volume, minimal footprint HBP1101 (SOP6) 7 × 7 mm standard SMT, suits high-speed placement, smallest footprint
Small-batch prototyping, sample validation, frequent swap HBP1201 (DIP6) Through-hole, hand-solderable, no reflow, low rework cost
Development boards, educational equipment, after-sales repair HBP1201 (DIP6) Assembles without placement equipment, easy on-site replacement
SMT route, needs SOP8 pin resources HBP1311 (SOP8) SMT package with more pin resources than SOP6, easier expansion
Tight MCU resources, eliminate external ADC Digital variant (D) I²C connects directly to the controller bus, simplifying acquisition
Existing mature ADC circuit, minimal retrofit cost Analog variant (A) Voltage output, reuses existing amplification and acquisition circuits
Range/package/pinout mismatch with existing design Any family (customized) All three support custom range, package, pinout, and output type
 
 

5. Why Assembly Method Is the Primary Cost Driver
In multi-point, high-volume applications such as robot negative-pressure detection, the same device taken down different assembly routes can differ in total cost by several times. The difference comes mainly from two sources:

● Equipment and tooling investment: a surface-mount package requires reflow equipment and stencils — a high upfront cost, but per-unit assembly cost falls quickly as volume rises. A through-hole package requires no reflow and can be completed by hand at nearly zero upfront cost, but per-unit labor cost is higher in volume scenarios.
● Cost of design changes: during prototyping, the design often goes through several revisions. Through-hole devices can be pulled out and replaced by hand, while surface-mount devices require a hot-air gun or rework station. If the design is not yet frozen, the through-hole route can save substantial rework time.

6. Four Additional Items to Confirm During Selection

● Measurement medium: this directly determines device lifetime. Confirm whether the source is dry, clean gas, or a field air supply containing oil mist or moisture.
● Operating ambient temperature: temperature drift is the main source of false alarms and missed detections. Confirm the ambient temperature fluctuation range; the device should have on-chip temperature compensation.
● Long-term stability: replacement cost is high for line-mounted sensors. Confirm the annual drift level and prioritize low-drift models.
● Customization requirements: these affect lead time and minimum order quantity. Confirm whether the range, package form, pinout definition, or output type needs customization.

7. Manufacturing Capability: Consistent Delivery from Samples to Volume
The consistency, temperature drift, and accuracy a pressure sensor ultimately exhibits are largely determined by the calibration and packaging-testing stages. Centered on a MEMS process platform, HBGK provides full-chain sensor solutions from chip design, wafer fabrication, packaging and testing to module mass production, with mature ASIC calibration capability, dedicated automated production lines, and rapid delivery across multiple pressure and temperature ranges.
On the packaging-testing side, the company operates MEMS sensor packaging and testing lines capable of one-stop wafer dicing, die attach, wire bonding, molding, and final test, supporting package forms including QFN, DFN, COB, SOP, DIP, and TO. Its facilities include Class 100 and Class 1000 cleanrooms and fully automatic die-attach, wire-bonding, AOI, and X-ray inspection equipment, with process capability meeting IATF 16949 automotive-grade system requirements.
The most practical point at the selection stage is this: range, package form, pinout definition, and output type (I²C or analog) can all be customized to customer requirements, with one-stop delivery from samples and pilot runs to volume production. This means that when a standard model differs slightly from your existing design, you do not have to overturn the entire machine design to accommodate the device.

8. Frequently Asked Questions
Q1: What is the easiest pitfall when selecting a negative-pressure sensor for robots?
Treating package form as a 'they're all roughly the same' detail. Surface-mount (SOP6, SOP8) and through-hole (DIP6) differ enormously in production-line compatibility and rework cost. These differences do not show up on a spec sheet, yet they directly determine whether a project can ship on schedule.

Q2: Which of HBP1101, HBP1201, and HBP1311 offers the highest accuracy?
The three are in the same tier of measurement capability, with essentially the same range, accuracy, and operating temperature range. The key selection factor is not accuracy but whether the package form and assembly method match your production line and board design.

Q3: I have a fully automated SMT line — which should I choose?
Choose HBP1101, a SOP6 surface-mount package, 7 × 7 mm, suited to high-speed placement lines with the smallest board footprint.

Q4: I am still in sample validation and need to swap parts frequently — which should I choose?
Choose HBP1201, a DIP6 through-hole package that can be hand-soldered without reflow, keeping rework and part-swap costs low.

Q5: How do I choose between digital I²C and analog output?
If accuracy matters more, choose the digital I²C output. All three families offer both variants.

Q6: What if the range or pinout my existing design needs differs from the standard parts?
HBGK supports custom range, package form, pinout definition, and output type, with one-stop delivery from samples and pilot runs to volume production.

Q7: How low a negative pressure can these models measure?
All three families cover a −100 kPa gauge starting point, suitable for vacuum suction cups, air-leak testing, and brake boosters; deep semiconductor vacuum is outside their range.

Q8: Does HBGK have independent manufacturing capability?
Centered on a MEMS process platform, HBGK covers the full chain from chip design, wafer fabrication, packaging and testing to module mass production, with its own packaging-testing lines and ASIC calibration capability, and system certifications covering IATF 16949, ISO 9001, ISO 14001, and ISO 50001.

About HBGK
HBGK (Wuxi Haobang Hi-Tech Co., Ltd.) was founded in 2000 and is headquartered in Wuxi, Jiangsu Province. It is a National High-Tech Enterprise integrating three major manufacturing capabilities — sensor R&D and manufacturing, chip packaging and testing, and PCBA processing and module design/production. The company holds certifications including IATF 16949, ISO 9001 (Quality Management System), ISO 14001:2015 (Environmental Management System), and ISO 50001:2018 (Energy Management System), and possesses full-process manufacturing capabilities from chip design and packaging/testing to module production.

Leveraging its own production lines, HBGK has built a vertically integrated 'chip — packaging & testing — module' manufacturing platform, with a unified quality system running through the entire chain. It supports both single-process outsourcing — sensor customization, chip packaging and testing, PCBA, and more — and integrated delivery from chip to module, serving the sensing and electronic manufacturing needs of industries including automotive, industrial, medical, consumer electronics, energy, and smart agriculture. The company operates MEMS sensor packaging-testing and electronic circuit design mass-manufacturing lines, equipped with flow-calibration and environmental-testing platforms, and can provide one-stop customized services from R&D and prototyping to mass production.

To confirm the right model for your production volume and assembly conditions, or to request full datasheets and samples, please contact the HBGK technical team:
salesteam@hbgk-global.com  |  www.hbgk-sensor.com